Updated manual. New C-b (set baudrate) command

picocom.1

@@ -88,6 +88,13 @@ character durations.
 .RS
 .RE
 .TP
+.B \f[B]C\-b\f[]
+Set baurdate.
+Prompts you to enter a baudrate numerically (in bps) and configures the
+serial port accordingly.
+.RS
+.RE
+.TP
 .B \f[B]C\-u\f[]
 Baud up.
 Increase the baud\-rate.
@@ -120,7 +127,7 @@ Cycle through parity settings (even, odd, none).
 .RS
 .RE
 .TP
-.B \f[B]C\-b\f[]
+.B \f[B]C\-i\f[]
 Cycle through databits\-number settings (5, 6, 7, 8).
 .RS
 .RE
@@ -327,9 +334,10 @@ also shown.
 .SH DISPLAY OF OPTIONS AND PORT SETTINGS
 .PP
 The "show program options" command (\f[B]C\-v\f[]), as well as the
-commands that change program options (\f[B]C\-u\f[], \f[B]C\-d\f[],
-\f[B]C\-f\f[], etc) print messages showing the current values (or the
-new values, if they were changed) for the respective options.
+commands that change program options (\f[B]C\-b\f[], \f[B]C\-u\f[],
+\f[B]C\-d\f[], \f[B]C\-f\f[], etc) print messages showing the current
+values (or the new values, if they were changed) for the respective
+options.
 If picocom determines that an actual serial\-port setting differs from
 the current value of the respective option (for whatever reason), then
 the value of the option is shown followed by the value of the actual

picocom.1.html

@@ -41,6 +41,9 @@
 <dt><strong>C-backslash</strong></dt>
 <dd><p>Generate a break sequence on the serial line. A break sequence is usually generated by marking (driving to logical one) the serial Tx line for an amount of time coresponding to several character durations.</p>
 </dd>
+<dt><strong>C-b</strong></dt>
+<dd><p>Set baurdate. Prompts you to enter a baudrate numerically (in bps) and configures the serial port accordingly.</p>
+</dd>
 <dt><strong>C-u</strong></dt>
 <dd><p>Baud up. Increase the baud-rate. The list of baud-rates stepped-through by this command is: 50, 75, 110, 134, 150, 200, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200. If <code>HIGH_BAUD</code> support is compiled-in, then the following baud-rates are also added to the list: 230400, 460800, 500000, 576000, 921600, 1000000, 1152000, 1500000, 2000000, 2500000, 3000000, 3500000, 4000000. Depending on you system, any of the higher baud rates may be missing.</p>
 </dd>
@@ -53,7 +56,7 @@
 <dt><strong>C-y</strong></dt>
 <dd><p>Cycle through parity settings (even, odd, none).</p>
 </dd>
-<dt><strong>C-b</strong></dt>
+<dt><strong>C-i</strong></dt>
 <dd><p>Cycle through databits-number settings (5, 6, 7, 8).</p>
 </dd>
 <dt><strong>C-j</strong></dt>
@@ -133,7 +136,7 @@
 </dd>
 </dl>
 <h1 id="display-of-options-and-port-settings">DISPLAY OF OPTIONS AND PORT SETTINGS</h1>
-<p>The &quot;show program options&quot; command (<strong>C-v</strong>), as well as the commands that change program options (<strong>C-u</strong>, <strong>C-d</strong>, <strong>C-f</strong>, etc) print messages showing the current values (or the new values, if they were changed) for the respective options. If picocom determines that an actual serial-port setting differs from the current value of the respective option (for whatever reason), then the value of the option is shown followed by the value of the actual serial-port setting in parenthesis. Example:</p>
+<p>The &quot;show program options&quot; command (<strong>C-v</strong>), as well as the commands that change program options (<strong>C-b</strong>, <strong>C-u</strong>, <strong>C-d</strong>, <strong>C-f</strong>, etc) print messages showing the current values (or the new values, if they were changed) for the respective options. If picocom determines that an actual serial-port setting differs from the current value of the respective option (for whatever reason), then the value of the option is shown followed by the value of the actual serial-port setting in parenthesis. Example:</p>
 <pre><code>*** baud: 115200 (9600) </code></pre>
 <p>This means that a baud rate of 115200bps has been selected (from the command line, or using commands that change the baudrate) but the serial-port is actually operating at 9600bps (the driver may not support the higher setting, and has silently replaced it with a safe default, or the setting may have been changed from outside picocom). If the option and the corresponding serial-port setting are the same, only a single value is shown. Example:</p>
 <pre><code>*** baud: 9600</code></pre>

picocom.1.md

@@ -81,6 +81,11 @@ here.
     Tx line for an amount of time coresponding to several character
     durations.
 
+**C-b**
+
+:   Set baurdate. Prompts you to enter a baudrate numerically (in bps)
+    and configures the serial port accordingly.
+
 **C-u**
 
 :   Baud up. Increase the baud-rate. The list of baud-rates
@@ -106,7 +111,7 @@ here.
 
 :   Cycle through parity settings (even, odd, none).
 
-**C-b**
+**C-i**
 
 :   Cycle through databits-number settings (5, 6, 7, 8).
 
@@ -270,10 +275,10 @@ Picocom accepts the following command-line options.
 # DISPLAY OF OPTIONS AND PORT SETTINGS 
 
 The "show program options" command (**C-v**), as well as the commands
-that change program options (**C-u**, **C-d**, **C-f**, etc) print
-messages showing the current values (or the new values, if they were
-changed) for the respective options. If picocom determines that an
-actual serial-port setting differs from the current value of the
+that change program options (**C-b**, **C-u**, **C-d**, **C-f**, etc)
+print messages showing the current values (or the new values, if they
+were changed) for the respective options. If picocom determines that
+an actual serial-port setting differs from the current value of the
 respective option (for whatever reason), then the value of the option
 is shown followed by the value of the actual serial-port setting in
 parenthesis. Example: